Best Home Theater Wall Plate 11.2

Plate 10 Dec 2022 10+ Comments Open

1. Legrand Q Theater Connection WP9009 WH V1

Legrand Q Theater Connection WP9009 WH V1

It is designed to be used with banana plugs, spades or bare wire. Banana plugs are easy to install and remove and have a 3/4" spacing. The mess of wire strung along your baseboards is eliminated by wall plates. An ideal addition for your home theater speaker wiring setup that works with audio players, and surround-sound speakers, the ON-Q Home Theater Speaker Walls are an ideal addition. There are certain things that fit. Banana plugs or stripped speaker wire are accepted by gold multi-way binding posts. The high quality home theater ring kit. The banana binding jack plug posts are made from high-quality gold-plated brass, which prevents oxidation. The On-q Home Theater Speaker Kit has gold-plate binding. It is easy to install and remove a wall. Wall plates eliminate the mess of wires. The plastic used in their wall plates is flame-retardant. It is easy to install and remove a wall. Wall plates eliminate the mess of wires. The plastic used in their wall plates is flame-retardant.

Brand: Legrand - Onq

👤The wiring came out of a hole in the wall. I wanted to make everyone happy so I looked for a way to bring wires to the receiver. The wires will be brought from inside the wall to the surface. It is neat. Attach the bare wire ends to the wall. On the outside, use banana-plug-terminated wires.

👤The item is of great quality. The plastic is large. There is a The front and back of the subs have a good and a bad connection. Who uses cables for speakers? I have to purchase a new pair of RCA/Coax connectors. It is ok to label. Instead of using "right rear" or " left rear", it uses " left surround" and "right surround". Which speakers are the surrounds for my 7.1 or 8.1 set up?

👤My husband and I have purchased six of these so far, and we may purchase three more once our basement is finished. It was hard to find black because our light switches, outlets, and wall covers are all black. We hid all the surround sound speaker wires in the living room and master bedroom because we wanted it to look flawless. We have a 5.1 Bose surround sound system with a receiver that cannot all be right next to each other, so these are great. I felt obligated to knock off 1 star because I went through too much drama to find out that the fixture and cover plate were missing. The picture used in the ad was changed to show the connection fixture and cover plate, but the main point of the ad was that the product came with an indestructible wall plate cover. The cover plates need to be bought separately. I am satisfied with the product, but I don't like false advertising and getting 3 separate orders just for them to say I didn't get the cover plates included. I told the first lady that I was fine with them if they weren't supposed to include the plates, but she insisted that they were included on two separate occasions and I had to email her to say they weren't included. I demanded that they send me cover plates for free, but got some from Lowes.

👤The home theater wall plate is perfect for my speakers. The inside connection is already set up for the subwoofer and you can use the wall for it. I used cat5 twisted pair wires for my surrounds because they were already in the wall, and this wall plate has solid, gold plated terminals. The package came with two identical wall plates for both ends.

👤I prefer the surround speakers grouped together, which is why I got these over the Monoprice equivalents. There are some things that are not mentioned in the description. Set screws are used for the connections on the back. I was able to make a connection with double the stranded wire. The set screw is a bit small and it was difficult to find a screwdriver small enough to fit into the recess. The banana plugs are on the front and accept a standard dual banana plug. The spacing is too large for a dual plug and I tried to double check my wiring polarity vertically. When you get it all set up with a switch plate, it will look professional. Very pleased with the appearance.

2. Fosmon Five Speaker Theater Plate

Fosmon Five Speaker Theater Plate

A high quality gold plated copper connection is built with Remium built. It is easy to install and remove with no special tools required. There is a color code. Matching binding posts on the front and back. Standard size single gang boxes are not included. Also, note: The cover plate has a larger opening area and can only be used with the wall plate. A clean and tidy installation can be achieved by eliminating the mess of wiring along the baseboards.

Brand: Fosmon

👤I was thrilled to find a 5-pair faceplate that fits in a single gang. It is not deep enough and it is badly designed. At first glance, it looks like a banana plug in the front and a jack in the back. If you attach banana plugs to your in-wall wires, you can plug them into the back side of the jack, instead of trying to squeeze 10 wires into hard to reach side-holes without shorts. No chance. I discovered that if you put banana jacks into the back, they won't fit into the front because they were made too short. What a stupid design.

👤Do you want to remove this from the wall plate it came with? Maybe put it in an existing dual gang wall plate. Not going to happen. If you are going to make something like a wall plate connection panel, make sure it is compatible with all the other products on the market. I have never seen this incompatibility before with these brands. There are problems with fitting banana jacks due to the spacing, but I didn't get that far. It's not an acceptable or sensible approach by the manufacturer.

👤Here's the thing. If you're going to charge twice as much as Monoprice, you might try to raise the quality of what you sell. The barrels of these jacks are very thin. The edges of the barrels are left sharp. It's sure to cause a lot of trouble when they tighten them on bare wire. What more could anyone want than a few strands of severed wire straddling the posts and shorting your amplifier or receiver? If you're going to use "flex tips", you should buy a spare set because they won't last long. My advice? If you're buying more than one, go to Monoprice. The shipping will be covered by the difference in price.

👤The product is well-made. There is a standard horizontal spacing for dual banana plugs. Banana plugs are needed to be sure there is no contact between rows of terminals. The opening of the plate is not standard Decora. This was a problem for me when I wanted a double gang face plate. My hack was to cut off one edge on the face plates and join them together with a sliding compound. This worked well. Just score the plates with the power saw, then cut them all the way with a hack saw, and finish with a file. If you cut all the way with the power saw, you'll break the plate.

👤I needed this product to run wires through a wall. I was able to do it with only two gangs because of the four speaker single gang adapters that I had. There is one note for the person who is installing. The cover plate opening is longer than the standard two and a half inch. If you install this in a multi gang outlet box with multi gang cover plate, it mounts perfectly. You will need to use the cover plate that comes with this one as a template to cut the opening in the multi gang cover plate.

3. Fosmon Quad Speaker Theater Plate

Fosmon Quad Speaker Theater Plate

A high quality gold plated copper connection is built with Remium built. It is easy to install and remove with no special tools required. There is a color code. Matching binding posts on the front and back. Standard size gang boxes are not included. A clean and tidy installation can be achieved by eliminating the mess of wiring along the baseboards.

Brand: Fosmon

👤It was almost five stars. It seems that all of these products are made in the same Chinese factory. The quality is reasonable for the price. The one that fits with a standard Decora wall plate cover is different from the five speaker wall plate. If you are okay with using the supplied wall plate cover, you should use two of these instead of the five speaker product. Some reviewers report issues with stripped threads. The reviews are correct, but you should let the seller know. This happened to me when I used the five speaker product. Some banana plugs are too long to fit in the speaker receptacle. This issue has been encountered by other reviewers.

👤The product is easy to install. Make sure you have your wires spliced before you install the wall plate. I used banana plugs to connect the wires from the wall to the receiver.

👤I bought three of these Quad speaker units and ganged them together in a three gang assembly to create a 13 speaker interface behind my receiver. The middle unit was modified to provide a custom interface by exchanging the bottom two binding posts for two subwoofer posts. I am very happy with the quality and convenience of this product, and I can definitely recommend it.

👤I put two of these next to each other for an 8 speaker connection because they were easy to install. It works because movies sound amazing.

👤A hole in the wall allowed the speaker cable to come out. I don't have a problem with adding my own labels.

👤The connecting point for my surround sound speaker system was the wall plate. You think you are getting two of them in the picture. It is a front and back picture. Banana plugs can only be used on one side. The other side has to be hardwired. It made for a clean installation.

👤You can swap out a terminal for a coax easily. I ran a line to my amplifier. It's working great!

👤It works well and has a high density. I removed the plate from the wall cover because I wanted to use it with a wall box. The new wall box fit the Decor style plate perfectly. The cross threaded one did tighten down. If needed, I would buy again.

👤Plates cracked on the wall. The plugs are great.

👤A good product, but beware! The holes for securing the plate do not match the overall size of the plate. I drilled new holes in the wall plate, so you have to either buy a plate mounting separately or drill new holes in the wall plate. The description should state that fact. I have no complaints about the product at all.

👤The Terminal macht bei wertigen Eindruck. Ich ist das Terminal, so I have a problem with der Mae. Leerdosen ist das Terminal. Im Trockenbau ist das aber der Ausschnitt.

👤Quality control could be better because they look good and generally do the job. I had to use banana plugs inside the wall box because one of the locking nuts wouldn't tighten down on the wire I was using. The included screws are not the standard north american thread, but they were a fine thread and I had some left over from a previous reno.

4. Cable Matters Triple Speaker Theater

Cable Matters Triple Speaker Theater

There are dual 5-inch foamed-mica reinforced woofers with wide-dispersion super tweeters. 3 gang 7.2 surround sound distribution wall plate can connect 7 speakers, 1 subwoofer and three devices with HDMI; install this audio video wall plate in a 3 gang low voltage mounting bracket for your home theater system; Speaker wire wall plate is 4.5 x 6.4 x 0.2 inches; mounting screws are The binding post on this 7.2 speaker wall plate has red terminals and can be used with banana plugs, spade connections, or bare 12 to 18 AWG speaker wires. Subwoofer wall plate with female couplers can be used to connect two RCA subwoofer cables hidden behind the wall. Common video resolutions include 4Kx2K (UHD), 3840x2160 and HD1080p. Home theater wall plates with gold-plated binding post and RCA connections provide a reliable connection and distribute authentic audio and video. The 7.2 speaker system wall plate has a lifetime warranty and is a professional looking installation. The 7.2 speaker system wall plate has a lifetime warranty and is a professional looking installation.

Brand: Cable Matters

👤I bought two sets of plates for speaker connections. Most speaker plates don't have an rcs connection for the subs and wouldn't work for me. These worked well for that purpose. Their white is a terrible match to Legrand. On Q. The plate is in an unfinished area in the basement, but in our great room they really stand out. I will have to remove the set in the great room and use individual keystones from Legrand to match. The Legrand keystone straps and wall plates are a perfect match for the Cable Matters Cat 6 keystones.

👤This product is poorly engineered. The plastic part that holds the metal terminals is too thick to fit against the wall. A very new person looks at the installation. I used the orange Carlon old work style open back brackets, which have an extremely this face plate, so that was not a problem. I tried to make it look professional by fussing with it for an hour. What a waste of time. I have a lot of electrical experience. This is a poor product.

👤The screws provided for installing into an electrical box were a joke. A tiny head that was stripped. I used the screws from the extra double gang blank cover plate. The face plate was fastened with the other screws. The most frustrating parts of Chinese products are the crappy screws. It must be a conspiracy to destroy the west.

👤I put my equipment in a closet. It can get complicated when you have surround sound. This makes it much easier to do. It would be great if it included the mounting brackets, but they are cheap.

👤It looks neat and professional, one time setup and saved time, I bought couple to use in my media room and living room, I need to switch my banana plugs.

👤It is easy to install and clear up messy wiring. I like this item because my HDMI cable tends to pull the connection out of alignment.

👤It was great for what I needed. I needed to have one speaker on the other side of the room and this was the one I found. It has a clean look. I painted a different wood wall plate to match the one on my wall.

👤I wish it had the option of jumbo sized outlets since you will most likely be cutting finished drywall to install them. romex is thick enough of a gauge to run behind the wall and stiff enough to run on its own. If you choose to use romex, be careful. Make sure the ground is cut back so you can't make a mistake. If they tailored this product to be compatible with romex or stranded wire, it would be 5 out of 5. If you overtighten, romex breaks easily.

👤I wanted something like this so that I could run the wiring for the speakers into a wall. The wall plate does a good job of presenting an attractive finish, and a dozen wires entering a wall can be attractive. I would buy more if the price were reasonable. I used screw-down terminations instead of banana plugs because I didn't want a wire to come loose and short. With 14 gauge wire, I was able to feed each conductor into the banana hole and bared wire out through the side hole, and then put it in place with the nut. This makes cable management easy and neat, and reduces the risk of interference and shorting between wires. There is limited thread under the nuts, so be careful how much you tighten them. I kept my fingers tight. Maybe an extra quarter-turn using grips. You will lose the threads if you go too far.

5. Cmple 1081 530 N Speaker Surround Distribution

Cmple 1081 530 N Speaker Surround Distribution

The 7.2 speaker wall plate is ideal for your home theater speaker wiring setup and works with audio players that support 7.2 surround sound speaker setup. The box is standard 2 gang. The wall mounted wire connection for five speakers is included with the stereo amplifier. It is easy to install. The front plate has dedicated labeling. Use with banana plugs. Up to 5 speakers and 2 subs can be connected. High quality. The binding posts are gold- plated and resistant to rust. A white plate with glossy finish and speaker banana plug terminals with high amperage and high wattage capabilities. There is a package that includes a Double-Gang 7.2 surround sound speaker wallplate. Includes mounting screws.

Brand: Cmple

👤I was expecting this to fit a standard wall plate and I was going to use it with my Dolby Atmos setup that has 11 wired speakers and 4 speakers in different zones in the houses. I had to come up with something. I bought 3 of these to have 15 plugs for my speakers and one passthrough brush for the cords. I tried to fit this with a standard 4 gang wall plate but it was not possible because of the extra plastic. I spent an hour grinding down the plastic on the face plate and got it to work. I would expect it to fit a standard wall plate.

👤Speaker wires are no longer poking out of the wall. There are no silly doctored faceplates anymore. I have all of my speakers wired in the wall, which is easy to install and move around. It took me 50 years to figure out the value of spending a few dollars to properly install and organize all of my entertainment systems cables, and now that I've done it, it's hard to believe how easy it was. A few minutes of up front work have replaced hours of wasted time trying to make sure I don't accidentally cross wires, because my system is cleaner, professionally installed, and a few minutes of up front work have replaced a few minutes of up front work. I would highly recommend this box to anyone installing an entertainment system.

👤I have an electrical wall box and 5 ceiling speakers. The plate allowed me to quickly connect the A/V receiver with a cable with banana plugs. It is easy to remove the banana cable from the A/V receiver when the electronics cabinet is moved. It took a while to install. I needed longer mounting screws for the electrical box because it was set back an inch. The speakers had cables that had banana plugs. The banana jacks on this plate allow banana plugs without interference, which was better than expected.

👤The binding posts on the back side were stripped out while trying to tighten things up. The engagement of the thread is poor. It's working for now. I'm going to replace it because I can't trust it. The sticker says "made in China" and it's not listed as aUL. Use this at your own risk. I used the ICC brand for everything else, but they don't make a three pair version. I'll buy their four pair version and just have one unused pair, which drives my OCD nuts. My connections are falling apart inside the wall, but it's better than that.

👤I have a media closet with surround sound speakers in it. Extra speaker wires come into the media closet because the tv can go on two different walls. I ordered two if these and put them in because I couldn't stand the mess of wires there. They seem to be well built, the finishes are good, and the terminals screw down tight. It can accept either bare wire or the banana jack style. I stuck the ends of the wire in the holes and tightened the screws. It worked well.

6. Fosmon Home Theater Wall Plate

Fosmon Home Theater Wall Plate

The gang box/mounting brackets are not included. It is easy to install and remove with no special tools required. Standard gang boxes have mounts. Matching binding posts on both sides with thumbscrews. Use with banana plugs, spades or bare wire. A clean and tidy installation can be achieved by eliminating the wiring along your baseboards. Depending on the depth of the gang box, banana plugs can be accommodated on both sides of the plate at the same time.

Brand: Fosmon

👤The speakers were installed with an amplifier. I was going to leave the speaker wires poking through the wall, but this made the install much cleaner. This makes for a great combo with the low voltage single gang faceplate adapter. It would be better if it included the labels for L and R, but I have no complaints. Excellent product and fast shipping.

👤No matter what it will not fit, holes will not line up. Most standard wall plates have a cover diameter that is big. It's a long story. I'm not talking about drilling your own holes, I'm talking about the one with multiple positive feedback. Garbage product by Amazon. Garbage is selling on Amazon lately.

👤I wish it was different. I wish they had been deeper so you could use banana plugs. All of them are on both sides. When installing the outside ones, be careful not to push the ones on the inside out. It's probably what you did if there was no sound from the speakers.

👤The construction is solid and the thumb nuts are worth the money. Not junky at all. It's beautiful.

👤The color coding bands that identify cable polarity are easy to remove. A more secure color coding scheme is what they should provide.

👤These plates are great. If you like, you can use banana plugs on both sides. There is room for it. I used a banana connection from Fosmon. That may have helped.

👤It's easy to install. It would be better if the fixings fitted a conventional back box.

👤The design of the rear of the actual plate prevents this unit from getting as close to the wall as it should. The Decora plate sits off the wall because of the thickness of the low-voltage brackets. The brackets are made of fomon. The photos are on the Amazon page. The area around the mounting hole is the same as the rear edge of the Decora plate. The area around the hole is where the front of the low-voltage bracket is located. The wall cannot be touched by the Decora plate. The casting of the plate is too thick. The plates would be mounted on electrical boxes with their front edges below the surface of the drywall. It is legal for low-voltage applications.

👤It worked out as expected. It was used with the mounting brackets. The barrel is not long enough to allow banana plugs in both ends. The wire or spade connection must be on one side. I connected the in-wall side with bare wire.

👤Artikel is in the standard of amerikanischer standard. Hab 2 x 3 von den 5er ist immer. Blende fr Heimkino. There is antwort von dem Lieferanten. Ihren Hersteller sowas beispielsweise beispielsweise, beispiel 3er die as set angeboten ist...

👤Ho dovuto, giuntare un cavo audio dell'impianto Home Theatre. Ho semplicemente svitato le giunzioni e tramite 2. Non ho avuto variazioni. Soddisfatto. A banana e staccano agevolmente.

7. Fosmon Surround Distribution Speakers Subwoofers

Fosmon Surround Distribution Speakers Subwoofers

Plug and play connections, 3.5 MM aux to a wire. The 3-Gang 7.2 surround sound distribution wall plate is compatible with 4K@60Hz and supports HDMI 2.0. The high-speed connecting devices are made of gold. The wall plate has a gold plated connection. The HDMI wall plate from Fosmon is a clean connection point for your audio/visual equipment. hiding cables in your walls is a way to remove cable clutter. All of your sound is included. This wall plate can be used to set up a surround sound system. This product has a limited lifetime warranty. Refer to the website for more information.

Brand: Fosmon

👤The plate was straight to the point and made my home theatre connections so easy to manage that I can just plug the receiver into the jacks. Behind the wall, cable management is done. I can't speak for the quality of the HDMI ports because I used this opening for a 6-port Keystone plate which I then used for the CAT6a network ports. I only mention it because there is a use case for someone to swap the included HDMI ports for something else that works better in their situation. As long as you have a standard Keystone plate, this can be done. A different plate can be installed just as quickly. The reason I removed a star from the review was because the jacks on the item were not good. After installing everything and mounting it to the wall, I was hit with a constant bass signal coming out of my woofer. I knew it wasn't coming from a specific source since my receiver was off. I removed the wall plate and found that the jack on the inside had broken and the plastic plug had been pushed through to the back. The signal pin was shorting the cable because of this. I moved the cable to the second jack and it broke the first one. I decided not to return the plate because I had some extra keystones and jacks that I just removed and put in this wall plate. There were no more breaking issues after that. If you buy this product, keep an eye on the sub jacks as the plastic looked brittle and could break over time.

👤3 of these were ordered. Two of the three have bad HDMI connections. I tried different cables and tried another outlet. After all of the work, I returned what I thought were faulty cables, but only one of my three actually function. I am going to swap the HDMI gang outlet for another brand because the speaker connections work on all three of them. A lot of work, a lot of problems, and a lot of wasted time. 1/3 of my order price was returned by the company because the gang outlet didn't work. I would try them again in the future. The stars were from 2 to 5. Customer support is great.

👤I like the fact that I can get a 7.2 wiring into one location. I don't need the HDMI because I wouldn't be using it in the walls. The option to include another four-set of post for the plate would be better. I was able to find an insert with eight posts and swap out the HDMI insert for it. This is a nice plate if I only did 7.2.

👤The wall plate cleaned up my cables. The wires and cables were fished out of my walls and put into a cabinet. I could have just bought a wall plate with a large hole in it to save a few bucks but the plate really adds that extra touch making it look very professional. The 6.1 configuration includes the Front Left, Front Right, Center, Surround Left, and Sub Woofer. You can also hook up 2 cables. The left, center, and right panel are released by the 6 screws on the wall plate. The front plate will be put back on after the panels are screwed to the low voltage 3 gang brackets. I used the PROS clean plate from the 3 gang low voltage brackets. The plugs glide in smoothly and are high quality. There is a The HDMI port supports both audio and video. The banana posts were loose upon arrival. It was easy to fix with a pair of pliers.

8. Legrand HT2103WHV1 Home Theater Connection

Legrand HT2103WHV1 Home Theater Connection

Excess cable can be stored in-wall and there is slack for convenient access to the back of the TV. The media center can be moved closer to the wall. A 125V receptacle is included. The cable access strap is easy to use. The total outlet is 2. The easy extension of electrical wiring is supported by the other products in the family.

Brand: Legrand

👤There are wires behind my TV. I wanted something that was durable, usable, and good looking. I like that the unit is not square so that furniture can be closer to the wall. Since the three main ports are decora, they can be changed out to be whatever you want. You can change the location of the power outlet. The mechanism for holding the unit on the wall is good. I've taken it off a few times and I haven't had any issues with it. I put a piece of lath at the top and bottom of the hole so that I wouldn't damage the drywall if I tightened the screws too tight. That makes for a good installation. The brush insert was the only thing I kept. I added a keystone plate instead of an outlet and replaced the screw-back speaker plates with ones that have more terminals. I replaced the silver screws with white ones. I'm very happy with this unit, even though I only used the shell. It is holding up a lot of hardware.

👤This uses standard Decora inserts. To get the connections I wanted, I swapped my own keystone plates in. If you need to get more cables to your TV, there's an additional knockout on the top. I like that it allows me to expand in the future. I wish it had the brush. There is a The bad? The screws are made of silver. It's not a big deal if your TV is in front of it, but it looks cheap to have metal screws. The outlet box for power is an old style one that you can find at big box stores. I expected a more elegant solution. It did the job and was easy to hook up. I didn't know how it would fit in a wall. It's your wall, but it should fit.

👤I took the opportunity to run my surround and subwoofer wiring under the house while I was remodeling it, and this box fit the bill. The box is easy to install and can be tailored to your liking. I replaced that section with a Legrand On-Q decora 4-port keystone plate because I didn't need the front speakers. I ran a patch cord up to the TV and hardwired the receiver and PS3 to the other ports.

👤We hired a professional to hang the tv and hang the wall mount. The outlet has a lot of plugs and space. The TV is flush on the wall. Exactly what we wanted.

👤It's a good way to clean up the installation.

👤Excited to install. The product seems to fit my needs. Thank you.

👤Speaker wire coming out of the wall is much cleaner. The brush plate was swapped out for a cat 6 wall plate.

9. Choice Select Theater Connection Plate

Choice Select Theater Connection Plate

Designed for home theater systems that have audio speakers. The gold-plated connectors have superior performance. The color-coded solderless ports are easy to use. Color matching screws are included. The dimensions are 4-7/8” x 4-7/8”

Brand: Choice Select

👤The screw mounts are for a single ganged box, but this is a double gang plate. The plugs in the back are not compatible with the wires. They are too small.

10. Fosmon HD8006 Surround Distribution Subwoofer

Fosmon HD8006 Surround Distribution Subwoofer

Conceal cables behind the wall in your media room for a professional looking installation and include a lifetime warranty for peace of mind. The Fosmon 3-Gang 7.1 surround sound distribution wall plate is compatible with 4K@60Hz. The high-speed connecting devices are made of gold. The wall plate has a gold plated connection. The HDMI wall plate from Fosmon is a clean connection point for your audio/visual equipment. hiding cables in your walls is a way to remove cable clutter. All of your sound is included. This wall plate can be used to set up a surround sound system. Banana jacks don't work with dual banana plugs. Only works with banana plugs.

Brand: Fosmon

👤The plate was straight to the point and made my home theatre connections so easy to manage that I can just plug the receiver into the jacks. Behind the wall, cable management is done. I can't speak for the quality of the HDMI ports because I used this opening for a 6-port Keystone plate which I then used for the CAT6a network ports. I only mention it because there is a use case for someone to swap the included HDMI ports for something else that works better in their situation. As long as you have a standard Keystone plate, this can be done. A different plate can be installed just as quickly. The reason I removed a star from the review was because the jacks on the item were not good. After installing everything and mounting it to the wall, I was hit with a constant bass signal coming out of my woofer. I knew it wasn't coming from a specific source since my receiver was off. I removed the wall plate and found that the jack on the inside had broken and the plastic plug had been pushed through to the back. The signal pin was shorting the cable because of this. I moved the cable to the second jack and it broke the first one. I decided not to return the plate because I had some extra keystones and jacks that I just removed and put in this wall plate. There were no more breaking issues after that. If you buy this product, keep an eye on the sub jacks as the plastic looked brittle and could break over time.

👤3 of these were ordered. Two of the three have bad HDMI connections. I tried different cables and tried another outlet. After all of the work, I returned what I thought were faulty cables, but only one of my three actually function. I am going to swap the HDMI gang outlet for another brand because the speaker connections work on all three of them. A lot of work, a lot of problems, and a lot of wasted time. 1/3 of my order price was returned by the company because the gang outlet didn't work. I would try them again in the future. The stars were from 2 to 5. Customer support is great.

👤I like the fact that I can get a 7.2 wiring into one location. I don't need the HDMI because I wouldn't be using it in the walls. The option to include another four-set of post for the plate would be better. I was able to find an insert with eight posts and swap out the HDMI insert for it. This is a nice plate if I only did 7.2.

👤The wall plate cleaned up my cables. The wires and cables were fished out of my walls and put into a cabinet. I could have just bought a wall plate with a large hole in it to save a few bucks but the plate really adds that extra touch making it look very professional. The 6.1 configuration includes the Front Left, Front Right, Center, Surround Left, and Sub Woofer. You can also hook up 2 cables. The left, center, and right panel are released by the 6 screws on the wall plate. The front plate will be put back on after the panels are screwed to the low voltage 3 gang brackets. I used the PROS clean plate from the 3 gang low voltage brackets. The plugs glide in smoothly and are high quality. There is a The HDMI port supports both audio and video. The banana posts were loose upon arrival. It was easy to fix with a pair of pliers.

11. Fosmon Surround Distribution Speakers Subwoofer

Fosmon Surround Distribution Speakers Subwoofer

The Multi-Purpose Cables Label is perfect for organizing cords. The gang box/mounting brackets are not included. It is easy to install and remove with no special tools required. The gang boxes have mounts on them. A clean and tidy installation can be achieved by eliminating the wiring along your baseboards. Matching binding posts on both sides with thumbscrews. 2 jacks. Up to 7 speakers and 2 subs can be connected. The front plate has dedicated labeling. Use with banana plugs. Depending on the depth of the gang box, banana plugs can be accommodated on both sides of the plate at the same time.

Brand: Fosmon

👤Since I was rebuilding the house, I decided to hide all the wires of my 5.2.4 system.

👤The problem is that the wall plate doesn't come with any white screws to mount to the standard 2-gang wall plate. If it stayed attached, it wouldn't be very durable, since they think you'll mount it directly to the wall. It's a mystery why the screws aren't included in the product. I am not the first person to review this model. They won't line up with most 2-gang boxes, but it would still be nice to have them.

👤The 7.2 Home Theater wall plate is very well made. The picture shows a 7.2 speaker wall plate, which is what the title description states. The price is pros. The cheapest 7.2 wall plate is well made, fits great with banana clips in-wall, and all necessary screw hardware is included. I used a label maker to label the ports the way I want them, and it works great. It was a great bang for your buck.

👤It was made well. If you need to spray paint the plastic plate a different color, the gold plated metal pieces can be removed and re-installed. The plugs fit neatly into the plate receptacle and are accepted for stranded speaker wire. The front and back of the plate have banana plugs or bare wires on them. Very pleased with appearance and performance. Would buy again. I have seen similar product at other stores and it was 2 to 3 times higher than at other stores.

👤You can get the same product in the stores for half the price. If you don't have the two gang back box, then you will need to make some wall modifications. The product itself was good, decent quality, and as good as anything I have purchased from Home Depot or Radio shack. Even if they had provided some labels for you to apply, it would have been better if you had a PC and a printer to make it.

👤There's not enough room for banana clips on both sides of the termination. If you push hard from one side, the tension on the other side will pop.

👤The hooks worked perfectly for my speaker system. I have a 5.1 system with 2 additional speakers in an adjacent room. I had a wiring mess. It's easy to install. Great look after. Really has a solid product. I connected my bare wire to the wall. I am using banana plugs. It makes a great connection between my receiver and speakers. My needs are slightly different so I bought the other side of my basement. Both products are great and would not hesitate to purchase them again.

👤I can't put banana plugs on both sides. I had to screw down a bare speaker wire connection on the back. I found that process annoying. I had to keep the wires short so that they would fit in the electrical box. The banana plug wouldn't go into it, so I had to drill out one of the plugs.

Summary

What is the best product for home theater wall plate 11.2?

Home theater wall plate 11.2 products from Legrand - Onq. In this article about home theater wall plate 11.2 you can see why people choose the product. Fosmon and Cable Matters are also good brands to look for when you are finding home theater wall plate 11.2.

What are the best brands for home theater wall plate 11.2?

Legrand - Onq, Fosmon and Cable Matters are some of the best brands that chosen by people for home theater wall plate 11.2. Find the detail in this article. Cmple, Legrand and Choice Select are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com